IC695CPE310-ACAT Central Processing Unit GE

The PACSystems* RX3i CPE310 can be used to perform real time control of machines, processes, and material handling systems. The CPU communicates with the programmer via the internal Ethernet port or a serial port.
It communicates with I/O and Intelligent Option modules over a dual PCI/serial backplane.
Features
■ Contains 10 Mbytes of user memory and 10 Mbytes of non-volatile flash user memory.
■ Battery-less retention of user memory.
■ Optional Energy Pack on system power loss powers CPU long enough to write user memory to nonvolatile storage (NVS).
■ Configurable data and program memory.
■ Programming in Ladder Diagram, Structured Text, Function Block Diagram, and C.
■ Supports auto-located Symbolic Variables that can use any amount of user memory.
■ Reference table sizes include 32Kbits for discrete %I and %Q and up to 32Kwords each for analog %AI and %AQ.
■ Supports most Series 90-30 modules and expansion racks. For supported I/O, Communications, Motion, and Intelligent modules, see the PACSystems RX3i Hardware and Installation Manual, GFK-2314.
■ Supports up to 512 program blocks. Maximum size for a block is 128KB.
■ Two serial ports: RS-485 and RS-232.
■ Embedded Ethernet interface supports a maximum of two programmer connections.
■ The rack-based Ethernet Interface module (IC695ETM001) supports a complete set of Ethernet functionality. For details, see TCP/IP Ethernet Communications, GFK-2224.
■ Time synchronization to SNTP Time Server on Ethernet network when used with a rack-based Ethernet module (IC695ETM001) version 5.0 or later.
■ Ability to display serial number and date code in programmer Device Information Details.
■ Ability to transfer applications to and from USB 2.0 A-type compatible RDSDs (removable data storage devices).
■ Compliant with EU RoHS Directive 2002/95/EC using the following exemptions identified in the Annex: 7(a), 7(c)-I and III, and 15.

IC695CPE310-ABAB

For initial start-up and configuration of the CPE310, complete the following steps. For details on CPE310 operation, refer to PACSystems CPU Reference Manual, GFK-2222R or later. If you are swapping a CPE310 with a CPU310 in an existing system, also refer to “Migrating RX3i CPU310 Applications to a CPE310” on page 4.
1. Remove the pull-tab from the Real Time Clock (RTC) battery, located on the back of the CPE310.
2. Remove power from the RX3i rack and install the CPE310. The CPE310 can be installed in any pair of slots in the RX3i Main rack, except the two highest-numbered slots.
3. Mount the Energy Pack on the left side of the module in slot 0 of the rack. Use cable IC695CBL001 to connect the Energy Pack to the connector on the bottom of the CPE310.
4. Apply power to the rack.
Note: When the Energy Pack is powered up for the first time, or is in a system that has been powered down long enough to completely discharge the Energy Pack, it may require a few seconds for it charge to its operating level. The CPU’s STATUS LED will blink green during this time.
5. Connect the CPE310 to the Ethernet network.
6. Using Proficy Machine Edition (PME) software, configure a CPE310 in an RX3i target and assign a new IP address to the embedded Ethernet interface.
The CPE310 has the same configuration parameters as the CPU310, with the following exceptions.
 Universal Serial Bus: The RDSD (USB) port is enabled by default in the Controller and in the Proficy Machine Edition hardware configuration.
If a configuration with Universal Serial Bus set to Disabled is stored to the CPE310, USB port operation can be restored by storing a configuration with the port enabled or by performing a Clear All operation (power cycling the CPU with the Energy Pack disconnected).
Note: The USB port is for transfer of application data only. It is not intended for permanent connection.
 Modbus Address Space Mapping is not supported.
 Ethernet configuration: The embedded Ethernet interface must be initially configured by downloading a CPE310 configuration to the RX3i from Machine Edition. To configure the embedded Ethernet interface in Machine Edition, expand the CPU slot to display the Ethernet daughterboard. The Settings tab for the embedded Ethernet module contains IP Address, Subnet Mask and Gateway IP Address. Consult your network administrator for the proper values for these parameters.